Standard surface protection film is good for two to four weeks outdoors in direct sun and up to six months indoors in 10–30°C storage out of the sun. STACBOND sets removal at 30 days after installation, and no later than six months after delivery. Past that the adhesive has changed — ultraviolet outdoors, storage time and temperature swings indoors — and a film meant to be temporary leaves glue behind.
- 2S Packaging Sdn Bhd
- ISO 9001:2015 certified
- Seri Kembangan, Selangor

Key takeaways
- Exposure sets the window, not the calendar: months indoors, weeks outdoors in direct sun.
- Specify by peel adhesion and thickness, not colour: 40 to 100 g for glass and high-gloss, 200 to 400 g for panels that take site handling.
- Ultraviolet is the outdoor driver; indoors it is storage time and temperature swings. Above about 60°C at the surface the adhesive softens.
Protection film is the low-tack film on a finished panel, so that fabrication, transport and installation damage lands on the film instead of the product. What nobody writes down for Malaysia is the clock. It is the detail behind the protection-film section of our specialty tape selection guide.
How long can surface protection film stay on a panel in Malaysia?
Surface protection film stays on for as long as its exposure allows, not for a fixed term. Standard PE film runs up to six months indoors in 10 to 30°C storage out of direct sun, and two to four weeks outdoors in direct sun. On an installed composite facade, STACBOND sets removal at 30 days after installation and no later than six months after delivery.
| Where the panel is sitting | Standard PE film | UV-stabilised film |
|---|---|---|
| Indoors, out of direct sun | Up to six months residue-free in 10–30°C storage; 60 to 90 days on aluminium profiles | Up to twelve months |
| Outdoors, direct sun | Two to four weeks maximum, off before day 30 | Eight to twelve weeks |
| Installed composite panel on a facade | 30 days after installation, or six months after delivery, whichever is first | |
Those indoor and outdoor windows come from a film manufacturer’s published guidance; the facade limits are from STACBOND’s transport and storage recommendations.
Malaysia sits at the hard end of those ranges. The Malaysian Meteorological Department records about six hours of sunshine per day and an annual temperature variation of less than 2°C: there is no cooler season in which the clock slows down.
Why does the film leave glue behind when it is left on too long?
Outdoors it is ultraviolet light, not age; indoors it is storage time and temperature swings. The adhesive is designed to let go; sunlight re-engineers it so it will not. Alucobond’s own installation and handling guideline is blunt about the cause: “To avoid residuals of glue sticking to the surface of the panels due to UV radiation, it is recommended to remove the protective foil as soon as possible after the installation.”
Heat is the other mechanism. Huayuan’s protective film FAQ puts the threshold at around 60°C at the surface: above that, held for a long period, the adhesive softens and transfers to the panel. STACBOND adds wide swings of storage temperature, which change the film’s adhesion and make it difficult to remove. Alucobond separately advises against storing panels longer than six months.
The reverse case is a carton tape letting go in a hot warehouse: why packing tape peels in Malaysian heat.
Which film do you specify for which surface?
Specify protection film by peel adhesion in grams and by thickness, not by colour. Glass and high-gloss finishes take a low-tack film at 40 to 100 g and 0.04 to 0.06 mm; composite panels and profiles that take site handling take a high-tack co-extruded film at 200 to 400 g and 0.06 to 0.15 mm. Those two numbers decide whether the film survives handling and still releases cleanly.
| Surface | What to ask for |
|---|---|
| Architectural glass, mirror-polished and high-gloss finishes | Low tack, 40 to 100 g, 0.04 to 0.06 mm, transparent for inspection before removal |
| Stainless steel sheet, aluminium sheet, coated metal | PE film that survives cutting and bending and still releases cleanly |
| Composite panels and uPVC profiles stored outdoors | Black-and-white co-extruded film, high tack at 200 to 400 g, 0.06 to 0.15 mm; the white face is the UV-reflecting side |
| Appliance, electronic and air-conditioner panels | Low-electrostatic PE carrier, so the film does not pull dust onto the surface |
The gram and thickness ranges above come from Huayuan’s published specification guidance; the cutting-and-bending line is Adtech Malaysia’s.
2S’s own protection tape is the general-purpose end of that table: a polyethylene carrier with a solvent-based acrylic adhesive at low tackiness, 50 micron, low-electrostatic, specified to come off without leaving glue residue, with glass in the building trade named as a primary application. The data sheet states no exposure window and no peel-adhesion figure, so ask for both on the quotation.
Where it is not the right answer, say so. Panels parked in the open for months want a UV-stabilised co-extruded film, not a clear low-tack film. Short-term cover for aluminium against rust and dirt is a job for black PVC protection tape, a PVC carrier with natural rubber adhesive. Contractors usually buy a set — see the tapes every building contractor needs, our packaging materials range and our tape and packaging FAQ.
What should you ask for when you order protection film?
Four lines in the enquiry decide the grade you are quoted: the substrate and where the panel will sit, and for how long, the peel adhesion in grams, the thickness, and whether anything will be written on the film. Most ordering mistakes are one of those lines missing, not a price.
- The substrate, and where the panel will sit and for how long. This is the line that chooses the grade.
- Peel adhesion in grams. Low tack for glass and high-gloss, higher for profiles.
- Thickness. Thin where you inspect through the film, thicker where the panel takes punishment.
- Whether anything will be written on it. Alucobond prohibits marking the film or the panel with ink, adhesive tape or stickers — solvents and plasticizers can damage the lacquered surface underneath.
How do you take the film off without marking the panel?
Take the film off in one pass across the whole visible face: STACBOND warns that partial removal can leave stains or marks on the front of the panel. Light adhesive left behind usually wipes away with isopropyl alcohol or a mild solvent.
- Peel at handover, not “eventually” — removal is a line on the programme with a date against it.
- Pull it back at about 45°, slowly — the film maker’s own clean-removal guidance.
- Test a hidden corner before any solvent, and use nothing abrasive.
- If panels wait outside, cover them. STACBOND’s instruction is an opaque cover, not reliance on the film.
Storage matters for the film roll too: the rules in handling and storing your tapes apply to a roll of protection film.
Frequently asked questions
How long can surface protection film stay on an aluminium panel in Malaysia?
Indoors out of the sun, a film manufacturer’s published figure for aluminium profiles is 60 to 90 days residue-free, and six months for standard film in 10–30°C storage. Outdoors in direct sun, two to four weeks is the limit. On an installed composite facade, STACBOND sets 30 days after installation.
Does surface protection film leave glue on glass?
Not if it is the right film and it comes off in time. Glass and high-gloss finishes want a low-tack film at 40 to 100 g peel adhesion and 0.04 to 0.06 mm. Residue comes down to too much tack for the surface, or too long in the sun.
What peel adhesion should I ask for on architectural glass?
40 to 100 g, transparent, so quality control can inspect through the film before removal. Profiles and composite panels that take cutting and site handling need the other end of the range, 200 to 400 g, usually a black-and-white co-extruded film, whose white face is the ultraviolet-reflecting side.
Can I write on the protective film with a marker?
No. Alucobond prohibits marking the protective film or the panel with ink, adhesive tape or stickers, because the solvents and plasticizers can damage the lacquered surface underneath. The prohibition covers tape and stickers as well as marker ink, so label the rack or the pallet instead.
Sources
ALUCOBOND Singapore installation, storage and handling guideline; STACBOND transport and storage recommendations; Huayuan protective film FAQ; Malaysian Meteorological Department, Climate of Malaysia; 2S protection tape specification, 2S black PVC protection tape; Adtech Malaysia, polyethylene surface protection film.
Talk to 2S Packaging
2S Packaging Sdn Bhd supplies industrial adhesive tapes and packaging materials from No 2, Jalan BS 9/12, Geo Industrial Park, Taman Bukit Serdang, Seksyen 9, 43300 Seri Kembangan, Selangor, and is ISO 9001:2015 certified. Tell us the substrate, where the panels will sit and for how long, and we will quote a film that matches.
WhatsApp 2S PackagingCall +603-8942 9960
2S Packaging Sdn Bhd · ISO 9001:2015 certified · No 2, Jalan BS 9/12, Geo Industrial Park, Taman Bukit Serdang, Seksyen 9, 43300 Seri Kembangan, Selangor


